View UPC8106TB_1151732.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

3 V SILICON RFIC UPC8106TB FREQUENCY UPCONVERTER
FEATURES
* RECOMMENDED OPERATING FREQUENCY: fRFout = 0.4 GHz to 2.0 GHz fIFin = 100 MHz to 400 MHz * SUPPLY VOLTAGE: VCC = 2.7 to 5.5 V * HIGH DENSITY SURFACE MOUNTING: 6 pin super mini mold package * LOW CARRIER LEAKAGE: Due to double balanced mixer * BUILT-IN POWER SAVE FUNCTION
LO Input GND IF Input
INTERNAL BLOCK DIAGRAM
(Top View)
3 2 1
4 VPS 5 VCC 6 RF Output
DESCRIPTION
NEC's UPC8106TB is a silicon RFIC designed as a frequency upconverter for cellular/cordless telephone transmitter stages and features improved intermodulation. This device is housed in a 6 pin super mini mold or SOT-363 package making it ideal for reducing system size. The UPC8106TB is manufactured using NEC's 20 GHz fT NESATTM III silicon bipolar process. NEC's stringent quality assurance and test procedures ensure the highest reliability and performance.
APPLICATION
* CELLULAR/CORDLESS TELEPHONE
ELECTRICAL CHARACTERISTICS
(TA = 25C, VCC = VRFout = 3 V, fIFin = 240 MHz, PLOin = -5 dBm, VPS 2.7 V unless otherwise specified) PART NUMBER PACKAGE OUTLINE SYMBOLS ICC CG PSAT OIP3 PARAMETERS AND CONDITIONS Circuit Current at VPS 2.7 V VPS = 0 V Conversion Gain at fRFout = 0.9 GHz, PIFin = -30 dBm fRFout = 1.9 GHz, PIFin = -30 dBm Saturated Output Power at fRFout = 0.9 GHz, PIFin = 0 dBm fRFout = 1.9 GHz, PIFin = 0 dBm Output Third-Order Intercept Point at fIFin1 = 240.0 MHz fIFin2 = 240.4 MHz PIFin = -20 dBm Third-Order Intermodulation Level at fIFin1 = 240 MHz fIFin2 = 240.4 MHz PIFin = -20 dBm SSB Noise Figure, fRFout = 0.9 GHz Power Save Rise Time at VPS: GNDVCC Power Save Fall Time at VPS: VCC GND UNITS mA A dB dB dBm dBm MIN 4.5 6 4 -4 -6.5 UPC8106TB S06 TYP 9 9 7 -2 -4 MAX 13.5 10 12 10
fRFout = 0.9 GHz fRFout = 1.9 GHz
dBm dBm
+5.5 +2.0
IM3
fRFout = 0.9 GHz fRFout = 1.9 GHz
dBc dBc dB S S
-31 -30 8.5 2.0 2.0
NF TPS(RISE) TPS(FALL)
California Eastern Laboratories
UPC8106TB ABSOLUTE MAXIMUM RATINGS1 (TA = 25C)
SYMBOLS VCC VPS PT TOP TSTG PIN PARAMETERS Supply Voltage Pins 5 & 6 Power Save Voltage Total Power Dissipation2 UNITS V V mW C C dBm RATINGS 6.0 6.0 200 -40 to +85 -55 to +150 +10
RECOMMENDED OPERATING CONDITIONS
SYMBOLS VCC TOP PLO fRFout fIFin PARAMETERS Supply Voltage1 Operating Temperature LO Input Level2 RF Output Frequency3 IF Input Frequency UNITS V C dBm GHz MHz MIN 2.7 -40 -10 0.4 100 TYP MAX 3.0 +25 -5 5.5 +85 0 2.5 400
Operating Temperature Storage Temperature Input Power
Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. Mounted on a 50 x 50 x 1.6 mm epoxy glass PWB (TA = +85C).
Notes: 1. The same voltage should be supplied to pin 5 and 6. 2. ZS = 50 (without matching). 3. With external matching circuit.
TYPICAL PERFORMANCE CURVES (TA = +25C, VCC = VRFout)
CURRENT vs. VOLTAGE
14 12 10 8 6 4 2 0 0 1 2 3 4 5 6 No Signal VCC = VPS 7 8
CURRENT vs. POWER SAVE VOLTAGE
12 VCC = 5.5 V 10
Cuurent, ICC (mA)
Cuurent, ICC (mA)
8
VCC = 3.0 V
6
4
2
0 0 1 2 3 4 5 6
Voltage, VCC (V)
Power Save Voltage, VPS (V)
CURRENT vs. TEMPERATURE
16 14 12
CONVERSION GAIN vs. VOLTAGE
12 11
Conversion Gain, CG (dB)
10 fRFout = 900 MHz 9 8 7 fRFout = 1.9 GHz 6 5 VCC = VPS 4 2 3 4 5 6
Cuurent, ICC (mA)
10 8 6 4 2 0 --60 --40 --20 0 20 40 60 80 100 VCC = VPS = 3.0 V No Signal
Temperature, TA (C)
Voltage, VCC (V)
UPC8106TB
TYPICAL PERFORMANCE CURVES (TA = +25C, VCC = VRFout)
CONVERSION GAIN vs. LOCAL INPUT LEVEL
15 fRFout = 900 MHz fLOin = 1140 MHz VCC = VPS = 3.0 V
CONVERSION GAIN vs. LOCAL INPUT LEVEL
15 fRFout = 1.9 GHz fLOin = 1.66 GHz VCC = VPS = 3.0 V
Conversion Gain, CG (dB)
12
Conversion Gain, CG (dB)
10
9
5
6
0
3
-5
0 -25 -20 -15 -10 -5 0 5 10 15
-10 -25 -20 -15 -10 -5 0 5 10 15
Local Input Level, PLOin (dBm) RF OUTPUT LEVEL AND IM3 vs. IF INPUT LEVEL
10 0 -10 -20 -30 -40 IM3 -50 -60 -70 -80 -40 -30 -20 -10 0 10 fRFout = 900 MHz fIFin1 = 240 MHz fIFin2 = 240.4 MHZ fLOin = 1440 MHz PLOin = -5 dBm VCC = VPS = 3.0 V
Local Input Level, PLOin (dBm)
RF Output level of Each Tone PRFout, (dBm) Third Order Intermodulation Distortion, IM3 (dBm)
RF Output level of Each Tone PRFout, (dBm) Third Order Intermodulation Distortion, IM3 (dBm)
RF OUTPUT LEVEL AND IM3 vs. IF INPUT LEVEL
10 0 -10 POUT -20 -30 -40 IM3 -50 -60 -70 -80 -40 -30 -20 -10 0 10 fRFout = 1.9 GHz fIFin1 = 240 MHz fIFin2 = 240.4 MHZ fLOin = 1660 MHz PLOin = -5 dBm VCC = VPS = 3.0 V
POUT
IF Input Level, PIFin (dBm)
IF Input Level, PIFin (dBm)
LOCAL LEAKAGE AT IF PIN vs. LOCAL INPUT FREQUENCY
0
LOCAL LEAKAGE AT RF PIN vs. LOCAL INPUT FREQUENCY
0
Local Leakage at RF Pin, LOrf (dBm)
Local Leakage at IF Pin, LOif (dBm)
-10
fRFout = 1.9 GHz PLOin = -5 dBm VCC = VPS = 3.0 V
-10
fRFout = 1.9 GHz PLOin = -5 dBm VCC = VPS = 3.0 V
-20
-20
-30
-30
-40
-40
-50 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
-50 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
Local Input Frequency, fLOin (MHz)
Local Input Frequency, fLOin (MHz)
UPC8106TB TYPICAL PERFORMANCE CURVES (TA = +25C, VCC = VRFout)
IF LEAKAGE AT RF PIN vs. IF INPUT FREQUENCY
0
IF Leakage at RF Pin, IFrf (dBm)
-10
fRFout = 1.9 GHz fLOin = 1.66 GHz PLOin = -5 dBm fIFin = -30 dBm VCC = VPS = 3.0 V
-20
-30
-40
-50 0 100 200 300 400 500 600
IF Input Frequency, fIFin (MHz)
S-PARAMETERS FOR EACH PORT (VCC = VPS = VRFout = 3.0 V )
LO port S11 Z REF 1.0 Units 2 200.0 mUnits/ 21.201 -53.748 hp LO port S22 Z REF 1.0 Units 2 200.0 mUnits/ 26.961 -87.312 hp
MARKER 1 1.15 GHz MARKER 2 1.65 GHz
MARKER 1 900 MHz MARKER 2 1.9 GHz
2 1
2
1
START 0.4 GHz
STOP 1.9 GHz
START 0.4 GHz
STOP 1.9 GHz
UPC8106TB S-PARAMETERS FOR EACH PORT (VCC = VPS = VRFout = 3.0 V )
IF port S11 Z REF 1.0 Units 1 200.0 mUnits/ 194.16 -579.53 hp
MARKER 1 240 MHz
1
START 0.1 GHz
STOP 0.4 GHz
S-PARAMETERS FOR MATCHED RF OUTPUT
(VCC = VPS = VRFout = 3.0 V ) - with TEST CIRCUITS 1 and 2 - (S22 data is monitored at RF connector on board.) 900 MHz (LC-matched) in test circuit S11 log MAG REF 0.0 dB 1 10.0 dB/ -19.567 dB hp 1.9 GHz (LC-matched) in test circuit S22 log MAG REF 0.0 dB 1 10.0 dB/ -15.213 dB hp
MARKER 1 900 MHz
MARKER 1 1.9 GHz
1>
1>
1
START 100 MHz S22 REF 1.0 Units 1 200.0 mUnits/ 36.59 2.9355 hp
STOP 3000 MHz
START 100 MHz S22 REF 1.0 Units 1 200.0 mUnits/ 58.191 -4.1191 hp
STOP 3000 MHz
MARKER 1 900 MHz
1
1
MARKER 1 1.9 GHz
START 100 MHz
STOP 3000 MHz
START 100 MHz
STOP 3000 MHz
UPC8106TB PIN FUNCTIONS
Pin No. Symbol Supply Voltage (V) - Pin1 Voltage (V) 1.3 Description Equivalent Circuit
1
IF Input
This pin is the IF input to the double balanced mixer. The input is a high impedance.
5
2 GND 0 - GND pin. Ground pattern on the board should be as wide as possible. Trace length should be kept as short as possible to minimize ground impedance. LO input pin. Recommended input level is -10 to 0 dBm. Supply voltage pin. This pin is the RF output. This pin is designed as an open collector. Due to the high impedance output, this pin requires an external LC matching circuit. Power save control pin. Bias controls operation as follows: Pin Bias VCC GND Control ON Power Save
3
6
3
LOIN
-
2.4
1
5 6
VCC
2.7 to 5.5
- -
RF Output 2.7 to 3.6
2
4
VPS
VCC/GND
-
VCC
5
4
GND
2
Note: 1. Each pin voltage is measured with VCC = VPS = VRFout = 3.0 V
UPC8106TB SYSTEM APPLICATION EXAMPLE
EXAMPLE OF DECT 900 MHz Cordless Phone
DEMO I Q
RX
SW
VCO
/N
PLL PLL
I
0 TX PA
UPC8106TB
Phase shifter
90
Q
UPC8106TB TEST CIRCUIT 1 (RFOUT = 900 MHz)
(Top View)
100 pF
3 LOin
VPS
4
Note 1
1000 pF
0.1 F
2 GND
100 pF
VCC
5
10 nH 1.0 pF
1000 pF 1000 pF
0.1 F
1 IFin
RFout 6
900 MHz Match
Note: 1. In case of unstable operation, connect 100 pF capacitor between pins 4 and 5.
TEST CIRCUIT 2 (RFOUT = 1.9 GHz)
(Top View)
100 pF
3 LOin
VPS
4
Note 1
1000 pF
0.1 F
2 GND
100 pF
VCC
5
100 nH TL = 5 nH
1000 pF 1000 pF
0.1 F
1 IFin
RFout 6
2.2 pF 1.9 GHz Match
Note: 1. In case of unstable operation, connect 100 pF capacitor between pins 4 and 5.
UPC8106TB OUTLINE DIMENSIONS (Units in mm)
PACKAGE OUTLINE S06
2.10.1 1.250.1
LEAD CONNECTIONS
(Top View) (Bottom View)
3
0.2 +0.1 -0
C2D
4 5 6
4 5 6
3 2 1
2.00.2 0.65 3 1.3 0.65 2
2 1
4
5
1
6
DOT ON BACK SIDE
0.9 0.1 0.7
1. 2. 3. 4. 5. 6.
IF INPUT GND LO INPUT POWER SAVE VCC RF OUTPUT
0 ~0.1
+0.1 0.15 -0.5
Note: All dimensions are typical unless otherwise specified.
ORDERING INFORMATION
PART NUMBER UPC8106TB-E3-A QTY 3K/Reel
Note: Embossed Tape, 8 mm wide, Pins 1, 2, and 3 face tape perforation side.
Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale.
EXCLUSIVE NORTH AMERICAN AGENT FOR
RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS
CALIFORNIA EASTERN LABORATORIES * Headquarters * 4590 Patrick Henry Drive * Santa Clara, CA 95054-1817 * (408) 988-3500 * Telex 34-6393 * FAX (408) 988-0279 24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) * Internet: http://WWW.CEL.COM 07/17/2000 DATA SUBJECT TO CHANGE WITHOUT NOTICE
4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279
Subject: Compliance with EU Directives
CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix -A indicates that the device is Pb-free. The -AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL's understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information.
Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*)
If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative.
Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL's liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.

▲Up To Search▲

Price & Availability of UPC8106TB

	To Download UPC8106TB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .